For optimum performance and continuous operation we use the units of the profile shaping machine SPM-LM-HYT/PMC-LM-HYT or the automatic profiler SPA/PAC. The machines are employed for panel lengths from 100mm.
All these versions are equipped as follows:
• Electronic length measurement in mm
• Hydraulic cut-off unit for right angle cross cuts, burr and torsion-free cutting after the profile shaping
operation automatic adjustment of cutting guides by the width adjustment of the profile shaping machine
• Bins to collect the cutting waste
SPM-LM-HYT/PMC-LM-HYT
Drive：2 stage brake motor for slow start-up and run-out
Controller：Present counter for the length, controlled by single operation
SPA/PAC
Drive: hydraulic drive with soft start and run-out controlled by a ramp
Controller: dialog controller for 10 different lengths and quantities, with setup mode, for single and continuous operation as well as manual operations, service program and selection of operating mode, as well as cut-off optimization.
Technical specifications for all versions of the SPM/PMC
| Type | Dimension (mm) | Weight | Intake width |
Axial dimensions |
Axial dim. 2 process runs |
Operating speed |
Infeed height |
||
| L | W | H | (kg) | (mm) | (mm) | (mm) | (m/min) | (mm) | |
| SPM 30/80 | 1250/1550 | 1470 | 1100 | 390 | 290-880 | 220-810 | 50-810 | 11 | 890 |
| SPM 30/80-RS(LS) | 1860 | 1470 | 1100 | 500 | 80-810 | ||||
| SPM 30/80-QA45 | 2850/3150 | 1800 | 1100 | 550 | 50-810 | ||||
| SPM 30/80-QA45-RS(LS) | 3450 | 1800 | 1100 | 660 | 80-810 | ||||
| SPM 30/80-HYT | 1550/1850 | 1500 | 1190 | 770 | 50-810 | ||||
| SPM 30/80-HYT-RS(LS) | 2150 | 1440 | 1190 | 880 | 80-810 | ||||
| SPA | 1450/1750 | 1500 | 1190 | 760 | 50-810 | ||||
| SPA-RS(LS) | 2060 | 1500 | 1190 | 870 | 80-810 | ||||
| PMC | 1500/1800 | 1470 | 1100 | 450 | 50-810 | ||||
| PMC-RS(LS) | 2110 | 1470 | 1100 | 560 | 80-810 | ||||
| PMC-QA45 | 3100/3400 | 1800 | 1100 | 630 | 50-810 | ||||
| PMC-QA45-RS(LS) | 3750 | 1800 | 1100 | 740 | 80-810 | ||||
| PMC-HYT | 1700/2000 | 1500 | 1190 | 700 | 50-810 | ||||
| PMC-HYT-RS(LS) | 2310 | 1500 | 1190 | 810 | 80-810 | ||||
| PAC | 1700/2000 | 1500 | 1190 | 850 | 50-810 | ||||
| PAC-RS(LS) | 2310 | 1500 | 1190 | 960 | 80-810 | ||||
| Gauges | Non-ferrous metals up to 0.8mm (up to 1.0mm when the roller gap is changed) Sheet steel up to 0.7mm Stainless steel up to 0.5mm |
||||||||